No Author Selected

By Daniele Rondoni, RDT

A middle-aged patient sought dental advice because she felt uncomfortable with the aesthetic appearance of her upper front jaw, specifically regions 11, 12, 21 and 22. Additionally, she was not happy about the diastema between her upper central incisors.

Fig. 1: Initial situation.

The oral examination showed four crown regions (12-22) and revealed that all of them have deteriorated. Tooth 21 had undergone an endodontic treatment, while teeth 11 to 22 have been newly built up. Due to the deteriorated conditions, all affected teeth were taken into consideration in the planning and designing of new restorations, including the intention to close the diastema between the width-to-length-ratio for the incisors.

The best suitable material for a natural look in combination with a close gingival attachment to the restoration is, in this case, zirconia, because of its biocompatibility and gentleness to the gingival region. The KATANA^TM Zirconia series from Kuraray Noritake Dental, offers a line-up of high-quality materials combined with true-to-life aesthetics, due to its natural color gradient within the material.

Fig. 2: Preparations, showing discoloration in the cervical area of tooth 21.

Fig. 3: Occlusal view of the preparations.

Fig. 4: The four zirconia crowns after designing followed by milling.

Fig. 5: Result directly after sintering.

To achieve an even more natural-looking and aesthetic restoration, CZR FC Paste Stains were used externally on the zirconia surface.

Fig. 6: Characterization of the restoration.

As often done, Cervical 2 was used to give an orange tint to the cervical area, to accentuate even better the natural tooth gradation. For the incisal areas, Grayish Blue in combination with Value was used to enhance transparency and opalescence. Same procedure applied to the approximal areas. Mamelon Orange 2 was used to reproduce dark orange stain on the mamelons.

Fig. 7: Result after cementation of the four new zirconia crowns. Their shape and chroma blend harmoniously with the arch.

Fig. 8: The vestibular view showing natural-looking characterization.

During a period of five years, annual check-ups showed intact crowns and a healthy gingiva. Additionally, the durability of the restorations, including their mechanical and optical properties revealed no signs of deterioration.

As the manager of a dental practice and the co-founder of the Deutsches Zahnärztinnen Symposium (DZÄS), an event that provides a forum for female dentists in Germany, Dr Frederike Fehrmann is an extremely busy woman. In this interview, she discusses her experiences as a woman working in dentistry and offers advice for those who are considering entering the field.

How did you decide to enter the field of dentistry?

I knew very early that I wanted to study dentistry. My mother is an orthodontist and I always liked what she was doing. During my studies, though, things looked different—I wanted to do oral and maxillofacial surgery for a period. But then I was offered the dental practice where I now work, and though it was different from what I had expected, I was still able to develop my skills in many directions, arriving finally at CAD/CAM and laser dentistry, which have been my favourite areas in recent years.

My professional life is constantly changing and developing, and that is what makes it exciting. High-tech dental surgery is exactly what I want to do and work with.

In your experience, are there any advantages or disadvantages to being a woman in dentistry? Have these changed over time?

I think dentistry is great, but it’s the same in this field as in many other professions in which women work. We often have a double burden simply because of our responsibility to bring the next generation into the world. This is a topic that has been on my mind for a long time. In fact, the DZÄS will be hosting a symposium in Frankfurt later this year where we will highlight the balancing act between technology and mindfulness, between career and family. I’m looking forward to it very much.

In my experience, women tend to have certain advantages—for example, we often find it easier to deal with children as patients than male dentists do. However, we still have to assert ourselves constantly. But things are changing. At the university near us, there are hardly any male dental students. It is time to rethink and adapt dental education to empower women to fulfil their potential.

How important is it to have peers and mentors with whom you can discuss dental issues?

Having other women with whom one can exchange ideas is worth its weight in gold. Sometimes you discuss your problems and suddenly find there is a simple answer that you yourself would not have thought of, one that makes your life easier. It’s possible to do without a mentor, of course, but things do become more difficult. Both peers and mentors make you strong and help you progress continuously. Besides, women often talk and listen differently and understand even without words.

What qualities and skills do you think are needed to succeed in the dental world?

I have had feedback from many patients who say that they like to see women providing treatment, as we can often read between the lines and might be more likely to recognise when they are afraid, for example.

Nevertheless, we frequently have to prove ourselves repeatedly. How often haven’t I heard the questions, especially as a young professional, “Are you able do that? Are you strong enough to remove that tooth?” I don’t think that a male dentist would be asked this.

Do you have any advice for girls and women considering a career in dentistry?

Just do it! Network and never, ever give up. Find a focus, something you do better than everyone else. Find mentors and colleagues who can help and guide you when needed. Educate yourself and find out what you’re passionate about.

Which Kuraray Noritake products do you employ in your daily workflow?

I use both KATANA™ AVENCIA™ Blocks and KATANA™ Zirconia Blocks in my CEREC workflow to produce CAD/CAM dentures. A colleague who works a lot with Kuraray Noritake told me about these blocks, and so I tried them out. The zirconia blocks impressed me by being super-translucent and variable in their colour texture. Their fit is excellent and the CEREC workflow is easy. The AVENCIA™ blocks are very simple to use because after milling they only need to be polished, not fired. This is particularly useful when supplying inlays.

Though traditionally a male-dominated discipline, dentistry is increasingly welcoming women into the fold, and female dental students now outnumber their male counterparts in many countries. The Paris-based dental surgeon Dr Anne Longuet Tuet recently spoke with Kuraray Noritake Dental about the challenges that women may face in dentistry and what it takes to succeed in this environment.

Dr Longuet Tuet, how did you decide to enter the field of dentistry?

I have always wanted to work in a medical profession. Initially, I wanted to be a veterinarian, but then, at a certain point, I spent a lot of time in a dentist’s office. She was also a woman, a teacher at the local university, and I saw what she could do and was inspired to help people in a similar way in order to let them smile again.

In your experience, are there any advantages or disadvantages to being a woman in dentistry? Has the situation changed over time?

I regularly lecture, and this still tends to be a very male-dominated arena. For example, at a lecture last year in Tunis, there were ten of us on stage and I was the only woman. Being a female lecturer can sometimes be a bit of a disadvantage, as we often have to work harder than the average male lecturer to prove ourselves and receive the same level of recognition. However, this will hopefully change in the future as more women prove themselves to be highly capable in this field.

Do you have any female mentors or role models in dentistry that you look up to?

Someone I really admire is Dr Francesca Vailati, who has contributed so much to modern adhesive dentistry through her lectures and research articles.

How important is it to have peers and mentors with whom you can have discussions?

I think it’s very important to have female peers and mentors, but it’s also worth remembering that men should also be part of your network. It’s nice to see other women when I give lectures or attend conferences, of course, but I also have plenty of male peers I admire and who help me grow professionally.

If you don’t consider men for mentorship, you can really limit yourself in the dental world, so it’s better to be open-minded in this respect. Good mentorship isn’t necessarily related to sex but instead to knowledge, experience, charisma and a willingness to share your expertise.

What do you need to succeed in the dental world?

I think the most important quality is a commitment to lifelong learning. It’s dangerous to think that you know everything there is to know about dentistry—there’s always an area in which you can improve. Even when you’re at a certain level and have been practising for many years, there’s always some new technology or technique that you can learn or something that you can improve on.

Of course, this is not just on the personal level. Dental materials and technologies are constantly evolving, and if you stop learning about them, you stop being up to date, right?

This is especially true if you work in adhesive dentistry. You need to be aware of the new bonding products and materials that are introduced to the market, since this can be a way of improving your work and the cases you treat.

How were you first introduced to Kuraray Noritake Dental’s wide range of adhesive solutions?

It was about four years ago, just after I really began to develop my restorative and adhesive dentistry skills. I was looking for a way to improve my composites and the way I bonded my ceramic restorations, and a friend of mine told me that the company’s CLEARFIL MAJESTY™ range of composites was very good. I was sent some samples soon afterwards and have been using the company’s products ever since.

Which Kuraray Noritake products do you use in your daily workflow?

Since 80% of my work at the practice is now restorative dentistry, I use the CLEARFIL MAJESTY™ ES-2 composite every day, as well as Kuraray’s PANAVIA™ adhesive cement. In addition, the dental lab that I work with uses KATANA™ Zirconia regularly to manufacture dental crowns.

To achieve excellence it is crucial to know the properties of modern materials and their correct clinical procedure. With this premise, surprising clinical results can also be achieved by combining different materials in the same clinical case.

This clinical case follows the aesthetic request of the patient who wanted to solve the pathology concerning the incisors with a direct composite restoration on 2.1 and a KATANA^TM STML crown on 1.1.

Following the mock-up the patient wanted larger incisor shapes with a strong character. The 2.1 was restored only with the MAJESTY^TM ES-2 Classic A2 mass exploiting the extraordinary ability of mimicry that comes from the Kuraray Noritake Dental light diffusion technology - LDT. The restoration on the 2.5 was performed with a CAD/CAM hybrid ceramic block - KATANA^TM AVENCIA^TM.

KATANA^TM AVENCIA^TM Block was characterized with a staining resin before cementation with the new PANAVIA^TM SA Cement Universal. PANAVIA^TM SA Cement Universal includes in its formulation a new type of silane coupling agent – LCSi monomer and this ensures strong and durable chemical bond to glass ceramics and composite resins without pretreatment with silane.

A strong and durable bond between the tooth and the restoration is a decisive factor influencing the long-term performance of dental restorations. The quality of the bond, however, is not only affected by the bonding agent or cementation solution used, but also by the condition of the bonding surface. For those who would like to ensure clean tooth and restoration surfaces in an easy way, Kuraray Noritake Dental has developed KATANA™ Cleaner, a universal cleaner with MDP salt and a pH of 4.5 for intra- and extra-oral application.

It has been proven that proteins present in saliva and blood have a negative effect on the performance of dental adhesives. Especially in indirect procedures, however, it is impossible to keep the bonding surfaces free of oral fluids. At try-in at the latest, the prepared tooth and the restoration are contaminated and need to be cleaned. Rinsing with water does not have the desired effect, and even with many available cleaners, a certain amount of proteins are usually left on the surface. Tests show that by using KATANA™ Cleaner or by sandblasting, the desired high cleaning effect needed is obtained, without compromising bond strength. This is true for KATANA™ Zirconia restorations, while KATANA™ Cleaner also leads to the desired results on dentin and enamel – surfaces in the oral cavity for which sandblasting and most of the other cleaners are not indicated.

The use of KATANA™ Cleaner offers yet another advantage: the cleaning procedure is extraordinarily simple, quick and neat. The universal cleaner comes in a bottle with an innovative flip-top cap, enabling single-handed dispensing onto the dish. It is then rubbed into the surface of the restoration and the prepared tooth structure or the abutment for ten seconds, rinsed with water and dried. Thanks to the high surface activity of MDP salt, these ten seconds are sufficient to remove the proteins on the substrate almost completely, creating conditions very similar to those found on a non-contaminated bonding surface. Subsequently, the selected bonding agent or cementation solution – e.g. PANAVIA™ V5 or PANAVIA™ SA Cement Universal – is applied according to the maufacturer’s usage instructions.

The result is a strong long-lasting bond, which gives users a peace of mind. Pilot users who have already tested the product agree that KATANA™ Cleaner is the easy way to optimise bond quality and streamline any adhesive procedure.

As co-editor-in-chief of the Journal of Adhesive Dentistry, Prof. Bart Van Meerbeek is one of the most respected authorities on the topic of dental bonding agents. Here, he discusses how they have advanced over the last three decades and what the future of adhesive dentistry might look like.

Prof. Van Meerbeek, how have bonding agents changed and advanced since you first began studying them?

I believe that the great progress dental adhesive technology has undergone in the last 30 years, and the progress in bonding agents in particular, has had a great impact on the field of dentistry and particularly on restorative dentistry, of course. Many of the current restorative dental procedures make use of adhesive materials and techniques and have advanced greatly compared with when I wrote my dissertation more than two decades ago on the topic of adhesion to dentine. Adhesion to enamel is, of course, relatively easy to achieve in comparison with adhesion to dentine, and when I first started researching this topic, I was limited to conducting clinical trials in which we were confronted with a relatively high number of restoration losses in the short term. I was lucky to have been able to witness first-hand the fast advancements dental bonding has made, having conducted research in this field now for nearly 30 years.

At a certain point, the research community started to realise that there is a smear layer in-between, which is created through cavity preparation, and that this layer interferes with bonding. If you want to achieve successful micromechanical and chemical bonding to the substrate, you first need to do something with this smear layer.

After this, we entered the era of conditioners and primers. In the past, the restorative community had been a little bit afraid of using phosphoric acid owing to its potential for pulp irritation. More and more, however, dental professionals began to use etchants with this chemical in them, as well as primers that effectively promoted bonding between the adhesive resin and dentine. While having achieved excellent bonding performance with multistep adhesives in the laboratory, as was later confirmed in clinical studies, further design and development of adhesive materials next focused on simplification and shortening of bonding procedures.

Out of this, two kinds of adhesives, making use essentially of two different bonding modes, arose: the etch-and-rinse adhesives and the self-etch, or etch-and-dry, adhesives. The newest generation of universal adhesives now enables dental practitioners to choose which of the two bonding modes to apply with one single adhesive formulation.

What advantages do bonded restorations offer over more traditional methods?

Bonded restorations are minimally invasive—the dentist doesn’t have to remove non-diseased tissue to create undercuts to keep the restoration in place, allowing for a more conservative approach. Keeping as much enamel as possible should be a goal of any restorative procedure, as it is simply the best tissue to bond to. Although bonding to dentine has always remained more challenging and has actually slowed down our adhesive endeavours for a long time, adhesively restoring teeth, involving also effective bonding to dentine, can today be achieved in a reliable, predictable and durable way.

Along with highly successful implantology to replace missing teeth, lessening the need for bridges, solitary tooth restorations have substantially increased in number. Bonding promoted the additional shift from conventional tissue-invasive crowns to tissue-preserving partial tooth restorations, as modern adhesives can hold such partial restorations in place on rather flat and even non-retentive surfaces. In addition, bonding procedures allow for more natural-appearing restorations to be achieved by techniques to adhesively lute aesthetic restorations made of glass-ceramics and even the strong zirconia ceramics that no longer can be considered non-bondable.

What is your opinion regarding the current generation of universal adhesive solutions?

I think that this generation is very good, but that they are still not always as good as the more traditional gold standard two-step self-etch and three-step etch-and-rinse adhesives when it comes to their intrinsic bonding potential to dental tissue. However, I do see it as a positive that many of these universal adhesives integrate the MDP monomer, which should be considered to be one of the best functional monomers available today, though it needs to be present at a high concentration and purity level.

The MDP monomer is, generally speaking, excellent at bonding to zirconia as well. When it comes to bonding to different kinds of ceramic as well as resin-based composite restorative materials, it is always helpful to know which universal adhesives contain silane and are claimed to no longer need further treatment of the restoration. This has the advantages of lower technique sensitivity and fewer procedural steps—provided that it does, of course, work. There is current scientific evidence that the silane incorporated in today’s acidic aqueous universal adhesives is, however, insufficiently stable. Fortunately, research is underway to develop new universal adhesives that contain other silanes with higher stability in water at higher acidity.

Overall, I believe that a restoration primer that contains a high concentration of silane along with the MDP monomer is still more effective than many universal adhesives for bonding to restorative materials, since these universal adhesives can contain many other ingredients that create a kind of competition within the material to reach and interact with the substrate surface, leading to lesser bonds.

Another shortcoming of universal adhesives is their thin film thickness and relatively high hydrophilicity, promoting water uptake and hence making them sensitive to hydrolytic degradation. In this light, it’s important to note that, when a viscous and hydrophobic flowable composite is applied on top of a universal adhesive, it can make up for this somewhat and allow for durable bonding to take place.

Is the MDP monomer crucial to the ultimate success of universal adhesives? Are there other factors that can influence this?

Well, it’s very clear that the MDP monomer is one of the most effective monomers available, given its primary chemical binding potential to hydroxyapatite. However, there are significant differences in the MDP monomer purity and concentration levels between these products, factors that are affected by whether or not the monomer is synthesised by the company itself or whether this process is outsourced. Essentially, a universal adhesive that contains a high concentration of very pure MDP monomer should perform the best.

Are there any specific advantages that a self-etch adhesive possesses?

The biggest advantage is that it doesn’t remove all hydroxyapatite and minerals present in dentine and so keeps the weaker dentinal collagen protected. Phosphoric-acid etching results in relatively deep and complete demineralisation with collagen exposure, making the bond more prone to degradation. Partially maintaining minerals around collagen using a mild self-etch adhesive additionally allows for strong ionic bond formation to take place when the adhesive in particular contains the functional monomer MDP. In addition, one should be aware that, while chemical binding doesn’t necessarily lead to higher bond strength, it can create better long-term bond durability.

What do you see as the next step in adhesive dentistry?

One possibility is to reduce the number of steps in the adhesion process with the final goal of having self-adhering restorative materials. There have been developments in this direction, including studies and commercial products, though the products haven’t always proved to be very effective and their bond durability is unclear. Now, however, there are newer materials coming to market with claims that they can be used with no pretreatment. Their clinical effectiveness, nevertheless, still needs to be proved and guaranteed before such self-adhering restorative materials could be used as true amalgam alternatives in routine dental practice.

Another possibility, and current R & D hype, is the development of bioactive adhesives. Many dental researchers and many companies want adhesives not only to deliver good bonding performance but also to have certain therapeutic benefits. What exactly a bioactive adhesive is depends on who you’re talking to. Some researchers believe that they should have antibacterial qualities, whereas others state that remineralisation of dentine and pulpal cell interaction are needed to qualify for the term “bioactive”. We certainly need to investigate whether we can give these materials these additional properties, but on one condition: that the adhesive material does not lose any of its original bonding abilities. That, in my opinion, is the biggest challenge for the future of adhesive dentistry.

By Japanese Dr. Shigeru Adachi, Cusp Dental Supply Co. Ltd

Initial situation

Checking of the shade (Posterior Crowns: FC Paste Stain, Anterior Crowns: Micro layered CERABIEN™ ZR)

Checking the restoration on the model

Final situation

Ceramist:

MDT Shigeru Adachi, Cusp Dental Supply Co. Ltd

MDT Adachi is a promising ceramist of the new generation, who has been working for Cusp Dental Supply Co. Ltd. since 2013. He received the Award of Excellence 2018 at QDT TECHNICAL CONTEST.

April, 2013 - Present
Working for Cusp Dental Supply Co., Ltd.
March, 2013
Graduated from the Osaka Ceramic Training Center
April, 2009 - March, 2011
Worked for Tsuruga Denatal Laboratory
March, 2009
Graduated from the Aishi Dental Technician College

MDT SHIGERU ADACHI USED KATANA™ ZIRCONIA HTML AND CZR FC PASTE STAIN FOR HIS CASE STUDY

By Irfan Abas
Dental implantologist & restorative dentist

Irfan Abas is a specialist in the field of oral implantology & restorative dentistry and an international speaker on the subject. He has given more than 20 presentations, workshops and live surgery courses throughout the world. TP - a dutch dental magazine, of which he is also editor, has published multiple articles under his name. Another highlight is a publication in the NTvT, in collaboration with Prof. Gert Meijer (Radboud UMC), under whose supervision Abas successfully completed the four-year postdoctoral training Reconstructive Dentistry in 2014. He is also an instructor and lecturer for the AAIE and chair of MINEC Netherlands. Irfan Abas has his own practice in Bussum, the Netherlands (tandartsabas.nl).

A healthy 42 year-old male patient requested reconstruction of his central incisors, which were badly worn.

Pre-Treatment

After producing the mock-up, grooves were prepared through the mock-up.

To fit two lithium disilicate veneers, a preparation of 1 mm was required. After removing the mock-up, the preparation was perfected.

Checking the space using a silicone mold.

Definitive preparation (frontal)

Temporary veneers made from temporary resin based material (Protemp)

Spot-etching before bonding the temporary veneers in place.

A small amount of flowable composite applied to the etched surfaces.

Light curing the entire surface of the temporary veneers.

Finished temporary veneers.

The veneers constructed by the dental technician.

Checking the fit of the veneers

Rubber dam fitted to enable controlled adhesive cementation.

Etching with 35% phosphoric acid K-Etchant Syringe for 10 seconds.

Treatment with selfetching primer PANAVIA™ V5 Tooth Primer (left on for 20 sec.)

Etching of the lithium disilicate veneers with hydrogen fluoride.

Clearfil Ceramic Primer Plus MDP-silane primer applied to the veneers.

Veneers secured to a placement instrument before definitive cementation

PANAVIA V5 Paste applied to the inner surface of the veneer.

PANAVIA V5 Paste spread over the veneer.

Veneer fitted and excess removed.

Light curing (minimum 10 sec.).

Immediately after the adhesive cementation with PANAVIA V5.

Immediately post-op.

Immediately post-op.

Two months post-op.

One year post-op.

One year post-op.

As the operator of his own dental practice in the German town of Laer and a member of the Digital Dental Academy in Berlin, Dr Hendrik Zellerhoff is clearly a very busy man. Fortunately, his integration of Kuraray Noritake Dental’s KATANA Zirconia Block into his daily workflow means that he is able to deliver high-quality restorations to his patients faster than ever. In this interview, Dr Zellerhoff explains how he uses the block and how his patients have responded to it.

Dr Zellerhoff, can you tell us a little bit about your background as a dentist?
In 2003, I began working as an assistant and at this time I worked with the CEREC system, a system for which I am now a certified trainer. In 2005, I opened my own dental practice in Laer, which I continue to operate to this day.

When did you first begin to work with Kuraray Noritake Dental’s range of products?
I think it was about four or five years ago that the laboratory that I worked with told me how good Kuraray Noritake’s KATANA Zirconia discs were for sintering and fabricating full-zirconia crowns. At that point, however, I was only looking for materials that would work with CEREC, and so it wasn’t until early 2018, when I went on a course in Leipzig in Germany where the KATANA Zirconia Block was being demonstrated, that I really saw how I could use this product in my practice. The block’s integration with the CEREC system means that it is now possible for me to provide high-strength aesthetic zirconia restorations for my patients accurately and quickly.

How frequently do you use the KATANA Zirconia Block during your daily work as a dentist?
I think around once a day, on average. It varies—sometimes I may make restorations for three different patients on one day, and then it’s four days until I use it again. My CEREC is only able to conduct wet milling, however, which is obviously slower than the 15-minute time span made possible through dry milling, and this limits how often I can use it.

What do you like most about this zirconia solution?
For me, it both feels and looks very real, so it has this aesthetic function going for it. Its multilayered, highly translucent appearance definitely helps to achieve more natural-looking restorations. However, the mechanical strength of the material is also something that I like, as it means that it can be used for restorations with thinner walls and sharper margins than those made with glass-ceramics.

With the release of the KATANA Zirconia Bridge Block, do you expect to use this zirconia solution more?
Oh, absolutely! The ability to make aesthetic bridges in the molar area and in a single visit is a revelation to me.

What has the response from your patients been?
They love it! These procedures can be realised on the same day as their initial appointment, and this means that my practice has patients coming from far outside of the small town in which I live. We even get people coming all the way from Switzerland to receive KATANA-based treatments—that’s how positive the response has been.

With this focus on digital dentistry, is there still a role for the dentist as a craftsperson?
I love to work with an entirely digital workflow. If a machine can do something better or faster than I am able to, then that is all right with me. As far as I can see, the future of dentistry will be digital. At the end of the day, the goal stays the same—to provide my patients with results that they are happy with.

With over 30 years of experience as a dentist and researcher, Dr Paolo Baldissara of the University of Bologna in Italy could be forgiven for slowing down a bit. This is far from happening, however, as he continues to be at the forefront of ceramic restoration material developments and their integration into CAD/CAM workflows.

When presenting at a symposium held in Berlin in Germany by Kuraray Europe earlier this year, Dr Baldissara highlighted how the company’s patented multilayered zirconia technology allows the KATANA™ Zirconia Block to effectively mimic the shade gradation of natural teeth. He commenced his presentation by outlining the general shift towards metal-free restorations, which in his opinion has been driven by a number of factors, the high value now placed on aesthetics in dentistry chief among them.

“I began using zirconia back in 2005 for prosthodontics in my department at Bologna, and it has greatly improved in quality since then,” said Dr Baldissara. “Generally speaking, the shift towards zirconia only started when a high-strength substitute for metal that was able to be processed with CAD/CAM systems with high accuracy became available.”

It was at the 2015 International Dental Show in Cologne in Germany where Dr Baldissara was first introduced to KATANA™ Zirconia UTML and STML, both of which impressed him with their high levels of translucency. “I started to use them almost immediately, mainly in their monolithic form, for research and in clinical practice,” he said. “My opinion of them was very high, as they allowed me to make cost-effective single crowns and multi-unit restorations with excellent aesthetic properties with scattered and diffused light. This is, ultimately, what patients want.”

Dr Baldissara began using the KATANA™ Zirconia Block in 2018 and expressed his excitement with how its high-speed sintering allows for fast processing of restorations. He recommended dry milling for a number of reasons: not only does it allow for the translucency of the zirconia to be maintained, it also helps to avoid contamination from other ceramic powders that may persist in the milling unit. In addition, he encouraged attendees to frequently replace the burs of their milling units for optimal results and reduced risk of chipping.

“Dry milling and high-speed sintering of the KATANA™ Zirconia Block is an extremely promising technology,” said Dr Baldissara. “In my opinion, it is the correct way to make aesthetic and mechanically strong restorations for the patient.”

“This profession requires incredible precision and focus”

Dr Magdalena Osiewicz has run her own private practice in Cracow in Poland since 2010 while also working as assistant professor at Jagiellonian University’s Department of Integrated Dentistry and as a researcher at the Academic Centre for Dentistry Amsterdam (Academisch Centrum Tandheelkunde Amsterdam) in the Netherlands. In this interview, she discusses what it takes to succeed in dentistry and why she relies on Kuraray Noritake Dental products in her dental practice.

Dr Osiewicz, how did you decide to enter the field of dentistry?

My father is a medical doctor and a great example for me. He argued that being a doctor would not be good for me because it would consume all my free time. Therefore, I decided that I would become a dentist, preferably a prosthodontist, and I have since specialised in dental prosthetics, restorative dentistry and treating temporomandibular disorders. However, I honestly think that being a dentist doesn’t leave you so much free time either. It’s an ongoing discussion that I have with my father during the holidays.

In your experience, are there any advantages or disadvantages to being a woman in dentistry? Has the situation changed over time?

I have been a dentist since 2005, and I must say that this profession requires incredible precision and focus as well as a very high level of physical fitness. In addition, it is a profession that demands that you have very good social skills and empathy for other people. Combined with all the other duties that a woman has, there can be big challenges for a woman working in dentistry.

How important is it to have peers and/or mentors with whom you can discuss problems?

I think it’s very important. Owing to the fact that we often work on our own, dentists can quickly forget that discussing issues with other professionals can improve their skills and help them serve their patients better.

What qualities and skills do you think are needed to succeed in the dental world?

To succeed in dentistry, you need to work with the best materials, constantly improve your knowledge and skills, and enjoy working with other people. You should always be open-minded and critically evaluate your work. Mistakes must not be repeated, and you should learn from them.

What advice would you have for women considering a career in dentistry?

I would advise them to maintain a healthy work–life balance and to take care of their physical and mental health.

How were you first introduced to Kuraray Noritake Dental’s wide range of solutions?

My first contact with Kuraray Noritake Dental’s products was during my postgraduate studies at the Academic Centre for Dentistry in Amsterdam, where we needed materials that could be used in the most extreme situations.

Which Kuraray Noritake products do you employ in your daily workflow?

To be honest, I use many Kuraray Noritake Dental products in my dental practice. CLEARFIL™ AP-X and PHOTO BRIGHT are great composites for patients with bruxism. I also use CLEARFIL MAJESTY™ ES-2 when we have a demanding patient for aesthetic work. I can recommend CLEARFIL™ PHOTO CORE, and I use PANAVIA™ for cementing prosthetic work as well as absolutely reliable adhesive systems such as CLEARFIL™ SE BOND or PHOTO BOND. I should also mention Kuraray Noritake’s range of KATANA™ Zirconia, which is the best zirconia on the market and is what I use for prosthodontics.