LabLine magazine is an English language publication catering to the field of lab-side dentistry. It provides comprehensive coverage of the latest techniques and trends in dental laboratory technology and materials, showcasing them via sophisticated, challenging and aesthetic clinical cases done by some of the most known experts in Europe. With its expertly curated content, LabLine serves as an invaluable resource for dental professionals seeking to enhance their knowledge and stay at the forefront of the industry.

In the SPRING edition of LabLine you can find a wonderful AESTHETIC CASE by Mikel Villar Gonzales and DT Pilar Ballesteros Galan. The patient, a 21-year-old female had a hypoplasia defect on her permanent teeth, 1.1 and 1.2., presumably due to trauma on her deciduous anterior teeth. Click the image below and check out how the case was done!

Case by Dr. David Garcia Baeza and DT. Pilar Ballesteros Galan

Shade determination in the planning phase, shade evaluation at try-in: How is it possible to accomplish these highly important tasks in the production of lifelike anterior restorations without meeting the patient in person? A computer-based shade documentation and try-in system is a great solution. Download this clinical case example describing the aesthetic restoration of two maxillary anterior teeth to learn more about one such system and its use!

Case by Dr. Yohei Sato, DMD, PhD, Department of Removable Prosthodontics, Tsurumi University School of Dental Medicine, JAPAN and Dr. Keisuke Ihara, CDT, i-Dental Lab, JAPAN

Fig. 1. The patient was referred to our hospital by an orthodontist. The chief complaints were improper esthetics of the teeth due to black triangles at the edges of the gaps between the teeth and occlusal wear of the teeth.

Fig. 2. On the basis of the pre-treatment diagnosis using a mockup, the abutments were prepared without anesthesia, keeping in mind that the enamel should be preserved to the extent possible.

Fig. 3. Since a fixation retainer was installed on the palate side, it was difficult to take impressions using silicone. Therefore, an intraoral scanner for impression taking was used.

Fig. 4. A layer of porcelain on each of KATANA™ Zirconia STML substrates was applied to complete the laminate veneer resto-rations. The inner surface of each restoration was sandblasted, being careful to prevent chipping.

Fig. 5. After trial fitting, bonding inhibiting substances as blood and saliva were removed using KATANA™ Cleaner.

Fig. 6. Milling. CLEARFIL™ CERAMIC PRIMER PLUS, which contains the phosphoric ester monomer MDP, was applied and dried using compressed air.

Fig. 7. The surface of each tooth was cleaned and treated with K-ETCHANT Syringe for 10 seconds before washing it away with water and compressed air-dried the area.

Fig. 8. PANAVIA™ V5 Tooth Primer was applied and left it for 20 seconds, then compressed air-dried it.

Fig. 9. PANAVIA™ Veneer LC Paste was applied and the laminate veneer was seated. For this case, we treated six teeth during one session.

Fig. 10. The unpolymerized excess paste was removed with a brush. PANAVIA™ Veneer LC Paste is a light-cured type, which was designed to provide sufficient working time.

Fig. 11. This photo shows the results after the final light curing. Since the excess cement was easily removed, there were almost no cement residues.

FINAL SITUATION

Fig. 12. The photo shows the inside of the oral cavity one month after the fitting of the laminate veneer restorations. It can also be noted that the teeth’s marginal gingiva has been improved, thanks to the good fit of the laminate veneer restorations.

The vacation period is over and we all are slowly returning back to our everyday routines and work. With all the travel and holidays in the last months you might have missed this great article in the LabLine Summer edition: Graftless solutions and implant-supported monolithic zirconia fixed prostheses.

It is an extensive, beautiful and detailed case report created and documented by team of well known and respected KOLs: Fortunato Alfonsi, Antonio Barone, Marco Stoppaccioli, Romeggio Stefano and Vincenzo Marchio.

Check it out by clicking here.

EKSEMPEL FRA CDT DANIELE RONDONI

Sædvanligvis kan det æstetiske potentiale i et dentalkeramisk materiale – specielt dets translucens – kun øges på bekostning af en nedsat bøjestyrke. Derfor har der manglet højtranslucente materialer, der er egnede til fremstilling af smukke monolitiske restaureringer, i form af lange broer. Lanceringen af dental zirkonia med forskellige niveauer af translucens og styrke i en enkelt disk har ændret på denne situation.

KATANA™ Zirconia YML fra Kuraray Noritake Dental Inc. er et sådant materiale. Det har en flerlagsstruktur med en høj bøjestyrke på 1.100 MPa, en høj chroma og en reduceret translucens i den nederste halvdel af disken. Selvom bøjestyrken og chroma er reduceret i den øvre del af disken og de incisale områder, øges materialets translucens opefter, ligesom i naturlige tænder. Dette giver et ubegrænset indikations-spektrum – forudsat at nogle design- og positioneringsregler overholdes. For at undersøge, om disse regler begrænser tandteknikerens designfleksibilitet, og om det æstetiske potentiale er højt nok til monolitiske anteriore restaureringer, har vi grundigt gennemtestet materialets bearbejdningsmæssige og optiske egenskaber. Følgende kliniske eksempel giver læserne et indblik i,
hvad der er muligt med dette innovative, flerlagede materiale.

Fig. 1. KATANA™ Zirconia YML 4- og 6-leddede broer efter fræsning og sintring. En naturlig facial overfladetekstur spiller en afgørende rolle, når der skal skabes
æstetiske monolitiske restaureringer.

Fig. 2. Okklusal visning af de to monolitiske broer. Den linguale overflades design sikrer gode muligheder for at opretholde god mundhygiejne.

Fig. 3. En lyskilde bag restaureringerne afslører den incisale translucens.

AFSLUTTENDE SITUATION

Fig. 4. Bukkal visning af den færdige 6-leddede bro, cementeret i patientens mund.

Fig. 5. Bukkal visning af den færdige 4-leddede bro, cementeret i patientens mund.

Med denne nye type af flerlaget zirkonia, er det muligt at producere æstetiske monolitiske restaureringer velegnet selv til brug i det anteriore område. Materialet byder på en høj designfleksibilitet trods dets graduerede styrke, og den høje translucens i incisalområdet sørger for et naturligt udseende efter sintring. Ultra-mikrolag og glasur på den monolitiske overflade vil være tilstrækkeligt til at levere resultater som kan tilfredsstille vores patienter.

DANIELE RONDONI, MDT

Born in Savona in 1961 where he lives and has worked in his own laboratory since 1982 with his collaborators. Graduated from the dental technician school IPSIA “P. Gaslini” in Genoa in 1979. He continued his education by attending relevant workshops for the “Italian dental school“ and broadened his professional experience in Switzerland, Germany and Japan. Since 2011 Kuraray Noritake Dental International Instructor.

Case by Francesco Ferretti and Marco Nicastro

Aesthetic restoration of anterior teeth using KATANA™ UTML Full anatomical crowns, with vestibular stratification and BOPT*¹.

^{*1 Biologically Oriented Preparation Technique}

Initial situation

Final result

Shows excellent aesthetic properties of KATANA™ UTML and the perfect integration in harmony with pink tissues.

Figure 1. The patient requested a solution for an aesthetic problem due to unnatural look of old restorations and black triangles coming from past history of periodontitis. The resulting retraction of the tissues had left the margins of the prosthesis clearly visible, and the loss of the papilla peaks, together with the numerous black spaces between the crowns, required a complex therapeutic approach.

Figure 2. The treatment plan for the periodontal problems con-sisted of a non-surgical approach, with scaling and root planing, and the replacement of the previously fixed prostheses to recondition the marginal tissues and facilitate the restoration of a new, aesthetically pleasing gingival architecture.

Figure 3. From a functional point of view, we decided to reduce the deep frontal bite to restore a correct overjet-overbite ratio. This reduction was also important from an aesthetic point of view, as it allowed us to shape the various elements correctly.

Figure 4. We usually remove old prostheses before beginning a periodontal treatment, and make a first, provisional restoration to create an environment in which the soft tissues can heal. If we have to work beyond the cement enamel joint (CEJ), we prefer a vertical preparation for posts, and the purpose of the provisional restoration is to condition the marginal tissues using Dr. Loi’s BOPT.

Figure 5. For the BOPT, the vertical preparation of the post has a finish line that extends inside the gingival sulcus. The temporary conditioning of the tissues induced by the provisional prosthesis allows us to modify the level of the gingival parables to a certain extent.

Figure 6. The image on the left shows the clinical healing of the tissues one month after the initial periodontal treatment. The role of the provisional restoration, appropriately realigned, is clear. The conditioning of the tissue has been achieved by means of the provisional restoration, which has modified the level and shape of the marginal tissue. Once filled with correctly fitted crowns, the interproximal spaces will be further reduced after the definitive restoration.

Figure 7. The correct management of the provisional restoration is crucial for the healing of the tissues. The placement of a provisional restoration before the periodontal therapy has allowed us to create the right environment for complete healing. At the same time, the vertical preparation has allowed us to gradually condition the marginal gingival tissue by shortening or lengthening the provisional restoration as necessary.

Figure 8. One of the advantages of a vertical preparation is that taking the final impression is easy, because the absence of a horizontal finish line greatly simplifies the procedure. On the other hand, the BOPT also requires the taking of an impression of the sub-gingival portion of the preparation. The dental technician will have to decide marginal shape of restorations according to the position of the gingival line in consultation of the clinician, and based on the tests conducted with the provisional restoration.

Figure 9. After the casting of the model, we prepared the gingival area to accommodate an ideal configuration of gingival parables.

Figure 10. After making a wax model, we assessed whether the height of the gingival zenith level could be further corrected. This photo shows that gingival level of 21 was not yet ideal, so we stretched it distally.

Figure 11. Once the wax model was complete, we extracted the element from the model and evaluated its protrusion. It was only after joining the gingival protrusion to the arbitrary margin of the preparation that we proceeded to a scan and milled the crowns.

Figure 12. The restoration was carried out with Katana™ UTML zirconia based on the new formulation of cubic zirconium oxide. This ultra tralucent material was chosen because we were working with light and non-discolored posts.

Figure 13. We finished the crowns on a positional impression to help to improve the gingival adaptation; we had some dispersion of the tissues in the first precision impression due to the use of retractors. We finished the crowns with CZR FC Paste Stain colours and glaze.

Figure 14. The surface colours and the slight contrast created are highlighted in this black-and-white image taken with a blue filter.

Figure 15. In this translucent image, we can see the natural translucent effect of KATANA™ UTML and invisible fusion between abutments and crowns.

Figure 16. Clinical image one year after cementation made with PANAVIA V5; this shows the good clinical condition of the marginal tissue, with no signs of inflammation or bleeding. The BOPT allowed us to optimise the level of the gingiva without resorting to periodontal surgery, while the shape of the new crowns has made it possible to close all interproximal spaces for an optimally aesthetic result.

Figure 17. The brightness of the restorations (thanks to the use of a particularly translucent zirconia) combined with the shape of the incisors, has greatly im-proved the aesthetic of the restoration, even though the condition initially appeared to be particularly unfavourable.

Figure 18. Compared to the previous prostheses, the incisal reduction allowed not only for the optimisation of the functional phase by reducing the overbite, but also made it possible to achieve a more natural aesthetic, with the contour of the incisal margins following that of the lower lip.

Dentists:

FRANCESCO FERRETTI

Born in Rome on 15th March 1957, Francesco Ferretti gets his degree as dental technician at the Institute “Edmondo de Amicis”, in Rome. In 1980, he starts working and, from 1987 to 1994, he cooperates with IVOCLAR VIVADENT giving consulting as ceramist. In 1992 he starts working exclusively with Prof. Mario MARTIGNONI.

• After one year cooperation with Prof. Martignoni, he starts working with the ORAL DESIGN CENTER founded in Rome by Mr. Willi Geller, and becomes a partner, improving prosthesis esthetics.
• Is registered outside the course of dentistry at the University of Rome Tor Vergata.
• In 2001, he founds ESTECH DENTAL STUDIOS, in cooperation with Pentron for technical training and consulting.
• He has published articles and studies in Italian and American magazines. He is interested in Metal Free techniques.
• Winner of the 2004 Polcan Aiop.
• He is a member of: ANTLO LAZIO ( National Association of Lab Owners) with the president of the Lazio region 2013-2014.
• National cultural manager ANTLO 2017-2020.
• Teacher of prosthetics perfectioning at the University of Chieti for the year 2002, he has been re-confirmed for the year 2003, 2004, 2005 to deal with Metal Free.
• Teacher of prosthetics perfectioning at the University of Naples 2006.
• He has participated as a speaker at numerous conferences in Italy. ESCD member has participated as a speaker at ten in Florence 2009 and Turin 2013.

MARCO NICASTRO

Marco Nicastro takes a degree in “Odontoiatria e Protesi Dentaria (Dentistry and Dental Prosthesis) at the University of Rome “ La Sapienza in 1989. Since the beginning he is interested in prosthesis restoration dentistry and aesthetic problems.

• From 1990 to 1996 he attends Prof. Martignoni’s studio, where he develops his prosthesis knowledge.
• From 1993 to 1998 he cooperates as lecturer with the Oral Design Centre in Rome, directed by Mr. Ferretti and Mr. Felli, giving lectures and courses about aesthetic restoration either in Italy or in foreign countries. In the same period he enlarges his experience in aesthetics, attending training courses at the University of Geneva, in Switzerland.
• Since 1993 he has been cooperating with Mr. Francesco Ferretti in the organization of Courses and Conferences, paying particular attention to metal free methodology.
• Vice President of the European Society of Cosmetic Dentistry (ESCD).
• Founding member and active member of Gimnasium interdisciplinary CAD-CAM (GICC).
• Active member of the Italian Society of Conservative Dentistry (SIDOC).
• Partner of the Italian Academy of Prosthetic Dentistry (AIOP).
• President of Like Mine Dental Education in Rome since 2001.
• He won, with Francesco Ferretti, the Polcan award of the Italian Accademy of Prosthetic Dentistry in 2004.

By Daniele Rondoni, RDT

Considering different criteria to select the ideal zirconia and frame design to meet the level of esthetics requested.

Step 1
Final Preparations.

Step 2
Zirconia Frame (KATANA Zirconia STML A2) cut-back designed to reproduce translucent incisal area.

Step 3
Application of 1st Internal Stain and firing.

Step 4
Application of 1st Luster, Clear Cervical and firing.

Step 5
Application of 2nd Internal Stain and firing.

Step 6
Application of 2nd Luster, and Opacious Body.

Step 7
Completion of firing.

Step 8
Completion of morphological correction.

Step 9
Post-operative view.

By Daniele Rondoni, RDT

Preoperative view

1 PFM. 3 Laminates on refractory

Postoperative view

NORITAKE SUPER PORCELAIN EX-3 CHROMATIC MAP

Dentist:

DANIELE RONDONI, RDT

Born in Savona in 1961 where he lives and has worked in his own laboratory since 1982 with his collaborators. Graduated from the dental technician school IPSIA “P. Gaslini” in Genoa in 1979. He continued his education by attending relevant workshops for the “Italian dental school“ and broadened his professional experience in Switzerland, Germany and Japan. Since 2011 Kuraray Noritake Dental International Instructor.

By D.T. Pier Francesco Golfarelli

Digital workflow and CAD/CAM shaping have now become a daily practice that helps to manage most cases, including the most extensive re-adaptations (rehabilitations).

KATANA™ HTML zirconia was selected, in consultation with the specialist, for the case presented here. It was principally chosen for its aesthetic and mechanical properties. One of our selection criteria was the advantageous lower abrasiveness level of zirconia. Because of its density, this material is less abrasive than the more traditional ceramics in combination with adequate mechanical polishing. Based on the initial situation, once the assembly in the articulator was completed, we designed a structure with anterior cutbacks for maximum aesthetics, while for the posterior teeth a monolithic solution was chosen for maximum strength and quality of the functional surfaces.

With the CORE & SHELL technique developed by the Noritake Italian Study Club, I can now fully exploit the optical properties of KATANA™ zirconia by integrating it, in the anterior area, with Noritake CERABIEN™ ZR ceramics. In the images here you can see the aesthetic results of the anterior and side areas, the mechanically polished monolithic surfaces and the special Noritake glaze.

Fig. 1 CAD Shaping - 3Shape Dental Designer

Fig. 2 Structure design with cutbacks

Fig. 3 KATANA™ HTML structure

Fig. 4 Occlusal surface – details

Fig. 5 Shade stain

Fig. 6 Shade Stain (SS)

Fig. 7 Core

Fig. 8 Internal Live Stain (ILS)

Fig. 9 Shell

Fig. 10 Shell Tissue

FINAL SITUATION

Fig. 11 Layering Details

Dentist:

D.T. Pier Francesco Golfarelli
Noritake Italian Study Club Teacher, Forlì

This case was conducted by Dr Davide Cortellini, owner of Studio Cortellini in Riccione in Italy, and dental technician Angelo Canale, owner of Canale dental laboratory in Rimini in Italy.

This patient came to the clinic to improve her chewing ability and aesthetic level. The physical examination revealed the presence of several endogenous erosive lesions that made chewing difficult, in addition to partly affecting the esthetics due to decrease in enamel thickness and the presence of dyschromic composite restorations. The possibility of using the new types of both tetragonal and cubic multilayer zirconia made it possible for us to plan the complete covering of all the elements with extremely conservative crowns with thicknesses between 0.5 and 1 mm in the axial and occlusal areas and up to 0.2 mm at the margin.

VERTICAL PREPARATIONS

Very conservative vertical preparations were carried out in the enamel without anesthesia. In the upper arch, the front group was prepared for full-veneer crowns, while the lower front group was treated with conventional lithium disilicate veneers without interproximal separation. In this case too, vertical preparations were carried out without finishing line. The impression was made using a 3Shape TRIOS intraoral scanner. The technician modeled the zirconia restorations that were then completed by the ceramist.

Knife Edge Preparation

SCANNING SEQUENCE

Digital DV models of temporary teeth

The three different materials were selected on the basis of the specific positions inside the mouth:

• UTML for the anterior teeth
• STML for the premolars
• HTML for the molars

The final result shows excellent integration between the 3 different types of zirconia and a good natural feeling.

MINIMAL PREP KATANA™ (KATANA™ MICRO LAYER)

HARMONIC OPTICAL INTEGRATION

The full-mouth rehabilitation procedure using three different types of zirconia led to a functional and beautiful treatment outcome. The optical integration between the materials is excellent and the high translucency especially in the anterior region creates a true-to-life appearance.

APPROACH WITH MINIMAL INVASIVE PREPARATIONS - REPORT ON THE SELECTION OF MULTI-LAYERED ZIRCONIA

Dental zirconia is no longer just the opaque framework material introduced two decades ago. Nowadays, it offers the high strength needed for long-span bridges, dentin-like translucency and strength perfect for thin-walled posterior crowns, or enamel-like optical properties for beautiful anterior restorations - depending on its composition and structure. Kuraray Noritake offers three types of dental zirconia - three with a multilayered structure created using patented powder coloring technology. They differ with regard to their optical and mechanical properties, which makes it possible to choose an ideal material for every clinical situation.

Dentists:

DR. DAVIDE CORTELLINI

Dr. Cortellini graduated with honours in Dentistry and Dental Prosthetics from the University of Siena in 1992. He won the scholarship of the Italian Society of Periodontology for the year 1994-95. He then received the opportunity to attend the Department of Periodontology and Fixed Prosthetics of Prof. NP. Lang at the University of Bern in Switzerland, carrying out clinical and research activities. He obtained the title of „Doctor Medicinae Dentium“ (D.M.D.) at the same university in 2000. Dr. Cortellini is the author of scientific publications in international journals of aesthetic dentistry. He is an active member and advisor to the Italian Academy of Prosthetic Dentistry, and a member of the International Academy for Digital Dental Medicine. He holds conferences in Italy and abroad and is dedicated to clinical activity in his own practice in Riccione, where he primarily focuses on aesthetic and digital prosthetics and complex prosthetic rehabilitation.

CDT. ANGELO CANALE

Mr. Canale is a dental technician graduated high school in 1981. He’s the owner of a dental laboratory in Rimini since 1986. He is specialized in fixed prosthesis on natural teeth and on implants with a metal free approach using different kind of materials. He is always interested about digital technique using CAD-CAM systems (in his laboratory the 80% of the work comes from digital impressions). He is co-author of international publications on PPAD, QDT, EJED and THE JOURNAL OF ADHESIVE DENTISTRY concerning the use of metal free in prosthesis. He is a speaker in national and international congress.